This machine has been sold.

2013 Caterpillar D6T



MACHINE SOLD



Machine Info:

Hours:5805
Serial Number:DTD01143
Stock Number:X21G0011
Machine Location:BILLINGS MT, 59101

Description:

2013 CAT D6T

Machine Details:

GENERAL APPEARANCE
Cleaning RequiredYes - Standard
Cab or CanopyGood
DecalsFair - Normal for age
FendersGood
Fuel TankGood
Grab IronsGood
HoodGood
Main Frame WeldsGood
PaintFair - Normal paint wear
Pre-Cleaner BowlGood
Sheet MetalGood
Steps / LadderGood
SAFETY ITEMS
ROPSYes
ROPS Certification PlateYes
HornGood
Parking Brake - SAFETY ITEMSFair - Switch worn- Replace.
GAUGES, OPERATOR STATION, CONSOLE
Dash ConsoleFair - Normal wear and sun fade.
GaugesGood
Glass/MirrorsGood
HeaterGood - To cold to test AC
Seat Cushion / Arm RestFair - Normal wear
SwitchesFair - Several worn- all functional.
Windshield WipersFair - Normal wear
ENGINE
Blow ByNo
Fluid Levels OK?Yes
KnockingNo
Oil LeaksYes - One minor on right side- filter housing may require re-sealed.
Air CleanersGood
Engine SupportsGood
Fuel Injection SystemGood
Operating Condition - ENGINEGood - Cold started well- normal power for hours
Turbocharger / BlowerGood
COOLING SYSTEM
Notes - COOLING SYSTEM - Normal wear- no leaks found.
CoolersGood
FanFair
HosesFair
RadiatorGood
Water PumpGood
ELECTRICAL, STARTING AND CHARGING SYSTEM
Batteries / CablesGood
StarterGood
TRANSMISSION
Leaks - TRANSMISSIONNo
Transmission - NoisyNo
Notes - TRANSMISSION - Trans shifted normally- no pile on site to test torque converter, but pulled well during brake test.
CaseGood
Controls - TRANSMISSIONGood
Operating Condition - TRANSMISSIONGood
Pump - TRANSMISSIONGood
SealsGood
Transmission - Forward ShiftsGood
Transmission - Reverse ShiftsGood
STEERING
Notes - STEERING - Steered well.
Differential Steering ControlsGood
Steering Operating ConditionGood
HYDRAULICS
Angle CylinderGood
Control Linkage - HYDRAULICSGood
Hose LinesGood
Lift CylindersGood
Overall Operating ConditionGood - Fully operational system- no leaks found.
Tilt CylinderGood
BLADE
Cutting Edge & BitsFair
Face / MoldboardFair - Normal wear
PinsFair - Normal wear
Push ArmGood
TrunnionsFair - Normal wear
RIPPER / GRAPPLE / WINCH
Brackets / StudsGood
Pins & BushingsGood
Ripper Lift CylinderGood
Shanks / GetFair - One shank installed- with worn tip.
UNDERCARRIAGE
Equalizer Bar - Good- dry seals
Notes - UNDERCARRIAGE - Full set of bottom guiding guards- only able to measure front bottom rollers.
Notes - UNDERCARRIAGE 1 - Full guiding guards- only able to measure front rollers- no evidence of leaks.
Notes - UNDERCARRIAGE 2 - Measured with both caliper and Ultra-sound.
Pivot Shaft - Good - dry seal
Pins & Bushings Turned?No
Track Frame - LeftGood
Track Frame - RightGood
Carrier Rollers Front
Links
Pins & Bushings (External)
Track Roller 1
FINAL DRIVES
Housings, LeftGood
Housings, RightGood
Planetaries / Differential, LeftGood
Planetaries / Differential, RightGood
COMMENTS, MISC. REPAIRS, GENERAL REMARKS
comment 1 - 1-21-2021 at 5,800 hours.


Specs from the manufacturer:

Dimensions
Drawbar Height (Center of Clevis) from Ground Face of Shoes23 in (58 cm)
Length - Track on Ground113 in (287 cm)
Engine
Bore4 in (11 cm)
Displacement537 cu in (0 m)
Engine ModelCat C9 ACERT
Flywheel Power200 hp (149 kw)
Gross Power213 hp (159 kw)
MakeCat
ModelC9 ACERT
Net Power185 hp (138 kw)
Net Power - Caterpillar185 hp (138 kw)
Net Power - EU 80/1269185 hp (138 kw)
Net Power - ISO 9249185 hp (138 kw)
Net Power - SAE J1349183 hp (136 kw)
Stroke6 in (15 cm)
Hydraulic Controls - Pump
Ripper Cylinder Flow50 gal/min (189 l/min)
Tilt Cylinder Flow21 gal/min (80 l/min)
Operating Specifications
Operating Weight40,550 lbs (18,393 kg)
Ripper
Beam Cross Section216 254 mm 8.5 10 in
Maximum Clearance Raised - Under Tip, Pinned in Bottom Hole20 in (51 cm)
Maximum Penetration20 in (50 cm)
Maximum Penetration Force14,557 lbs (6,603 kg)
Number of Pockets3
Overall Beam Width87 in (221 cm)
Pry-Out Force20,137 lbs (9,134 kg)
Ripper TypeFixed Parallelogram
Weight - Each Additional Shank163 lbs (74 kg)
Weight - With One Shank3,606 lbs (1,636 kg)
Service Refill Capacities
Cooling System20 gal (77 l)
Engine Crankcase7 gal (28 l)
Final Drive - Each4 gal (14 l)
Fuel Tank112 gal (424 l)
Hydraulic Tank14 gal (51 l)
Pivot Shaft Compartment1 gal (5 l)
Power Train39 gal (146 l)
Roller Frames - Each7 gal (25 l)
Standards
BrakesBrakes meet criterion SAE J/ISO 10265 MAR99
Transmission
2 Forward3 mph (5 kph)
2 Reverse4 mph (7 kph)
3 Forward5 mph (9 kph)
3 Reverse7 mph (11 kph)
3.5 Reverse9 mph (15 kph)
Undercarriage
Ground Pressure9 psi
Grouser Height3 in (7 cm)
Winch
Drum Capacity - 22 mm (0.88 in)290 ft in (737 cm)
Drum Capacity - 25 mm (1.0 in)220 ft (67 m)
Drum Capacity - 29 mm (1.13 in)220 ft in (559 cm)
Drum Diameter10 in (25 cm)
Drum Width13 in (33 cm)
Ferrule Size (O.D. Length)54 67 mm 2.10 2.63 in
Flange Diameter20 in (50 cm)
Increased Tractor Length - LGP16 in (40 cm)
Increased Tractor Length - STD20 in (52 cm)
Increased Tractor Length - XL/XW20 in (52 cm)
Oil Capacity18 gal (67 l)
Weight2,600 lbs (1,179 kg)
Winch and Bracket Length48 in (121 cm)
Winch Case - Width38 in (98 cm)

Dealer Contact Info:

Tractor and Equipment CAT


Click for Phone Number







ceg-logo ceg-logo ceg-logo ceg-logo ceg-logo