Construction Equipment Guide
470 Maryland Drive
Fort Washington, PA 19034
800-523-2200
The Caterpillar D3G is a compact crawler dozer designed for grading, site preparation, land clearing, and general earthmoving work. It is part of Caterpillar's D3 series and is commonly used in construction, landscaping, utility, and agricultural applications. The D3G features a tracked undercarriage for traction and stability on soft or uneven ground, along with a dozer blade for pushing, leveling, and backfilling material. Typical configurations may include a hydrostatic transmission, enclosed operator station, and compatibility with various blade and attachment options. The Caterpillar D3G is valued for maneuverability, control, and versatility in confined jobsite conditions.
| Flow at 6890 kPa - (1000 psi) | 16.10 US gpm (61.10 L/min) - Starting 2006 |
|---|---|
| Installed weights - Ripper with standard shank | 1,220.00 lbs (554.00 kg) - Starting 2006 |
| Lift Relief Valve - Setting | 2,900.00 psi (20,000.00 kPa) - Starting 2001 |
| Mounting Point | Fender - Starting 2001 |
| Number of Valves | 3 or 4 - Starting 2001 |
| Ripper Beam - Number of Pockets | 3 - Starting 2001 |
| Ripper Beam - O Overall width | 67.00 in (1.71 m) - Starting 2001 |
| Ripper Beam - P Height | 6.50 in (165.00 mm) - Starting 2001 |
| Ripper Beam - Q Length | 7.50 in (190.00 mm) - Starting 2001 |
| Ripper Beam - T Pocket Spacing | 31.00 in (775.00 mm) - Starting 2001 |
| Ripper Beam - U Shank Gauge | 61.00 in (1.55 m) - Starting 2001 |
| Ripper Beam - V Track clearance with - Installed weights - Ripper with standard - shank | 1,220.00 lbs (554.00 kg) - Starting 2001 |
| Ripper Beam - V Track clearance with - standard shoe | 4.40 in (113.00 mm) - Starting 2001 |
| Ripper Forces: - Penetration Force | 4,970.00 lbf (2,250.00 kgf) - Starting 2001 |
| Ripper Forces: - Pryout Force | 9,900.00 lbf (44.00 kN) - Starting 2001 |
| Ripper Shank - G Maximum digging depth | 13.30 in (337.00 mm) - Starting 2001 |
| Ripper Shank - L Maximum reach at - ground line | 29.00 in (739.00 mm) - Starting 2001 |
| Ripper Shank - M Maximum ground - clearance under tip (shank pinned in bottom hole) | 16.00 in (412.00 mm) - Starting 2001 |
| Ripper Shank - N Maximum ramp angle, - ripper up (shank pinned in bottom hole) | 26 deg - Starting 2001 |
| Ripper Type | Fixed Parallelogram - Starting 2001 |
| Tank Capacity (Oil) | 12.00 US gal (47.00 L) - Starting 2001 |
| Weight Installed | 36.00 lbs (16.00 kg) - Starting 2001 |
| Blade Capacity - Intermediate | 1.9 cu yd |
|---|---|
| Blade Capacity - Lgp | 2 cu yd |
| Blade Capacity - Xl | 1.9 cu yd |
| Blade Height - Intermediate | 33.20 in (84.33 cm) |
| Blade Height - Lgp | 33.20 in (84.33 cm) |
| Blade Height - Xl | 36.80 in (93.47 cm) |
| Blade Width - Intermediate | 115.00 in (292.10 cm) |
| Blade Width - Lgp | 123.90 in (314.71 cm) |
| Blade Width - Xl | 96.90 in (246.13 cm) |
| Digging Depth - Intermediate | 20.70 in (52.58 cm) |
| Digging Depth - Lgp | 20.70 in (52.58 cm) |
| Digging Depth - Xl | 21.80 in (55.37 cm) |
| Ground Clearance | 1.23 ft (0.37 m) |
|---|---|
| Height | 8.75 ft (2.67 m) |
| Height To Top Of Cab | 8.92 ft (2.72 m) |
| Length | 13.17 ft (4.01 m) |
| Length Of Track On Ground | 10.19 ft (3.11 m) |
| Length W/ Blade | 13.19 ft (4.02 m) |
| Length W/O Blade | 10.19 ft (3.11 m) |
| Weight | 16,227.00 lbs (7,360.45 kg) |
| Width | 6.08 ft (1.85 m) |
| Width Over Tracks | 6.09 ft (1.86 m) |
| Bore | 3.70 in (9.40 cm) |
|---|---|
| Caterpillar | 70.00 hp (52.20 kw) |
| Displacement | 305.00 cu in (4,998.07 cu cm) |
| Eec 80/1269 | 70.00 hp (52.20 kw) |
| Engine Make | 2236 |
| Engine Model | Cat 3046T |
| Gross Power | 77.00 hp (57.42 kw) |
| Iso 9249 | 70.00 hp (52.20 kw) |
| Net Power | 70.00 hp (52.20 kw) |
| Power - Gross | 77.00 hp (57.42 kw) |
| Power - Net | 70.00 hp (52.20 kw) |
| Power Measured @ | 2200 rpm |
| Sae J1349 | 70.00 hp (52.20 kw) |
| Stroke | 4.70 in (11.94 cm) |
| Pump Output | 16.10 gpm (60.94 lpm) |
|---|---|
| Relief Valve Setting | 2900 psi |
| Pump Flow Capacity | 2,900.00 gpm (10,976.50 lpm) |
|---|---|
| Relief Valve Pressure | 8.9 psi |
| Cooling System Fluid Capacity | 5.50 gal (20.82 l) |
|---|---|
| Engine Oil Capacity | 3.40 gal (12.87 l) |
| Final Drives Fluid Capacity | 3.60 gal (13.63 l) |
| Fuel Capacity | 43.60 gal (165.03 l) |
| Hydraulic Fluid Capacity | 12.00 gal (45.42 l) |
| Operating Weight | 16,227.00 lbs (7,360.45 kg) |
| Height | 6.50 in (16.51 cm) |
|---|---|
| Maximum Digging Depth | 13.30 in (33.78 cm) |
| Maximum Ground Clearance Under Tip | 16.20 in (41.15 cm) |
| Maximum Reach - Ground Line | 29.10 in (73.91 cm) |
| Number Of Shanks | 3 |
| Overall Width | 67.30 in (170.94 cm) |
| Ripper Type | Parallelogram |
| Weight | 1,241.00 lbs (562.91 kg) |
| Cooling System | 5.50 gal (20.82 l) |
|---|---|
| Crankcase - With Filter | 3.40 gal (12.87 l) |
| Final Drive - Each - Lgp | 5.40 gal (20.44 l) |
| Final Drive - Each - Xl | 3.60 gal (13.63 l) |
| Fuel Tank | 43.60 gal (165.03 l) |
| Transmission - Hydraulic Tank | 12.00 gal (45.42 l) |
| Blade Angle (Both Directions) | 25 degrees |
|---|---|
| Capacity | 1.9 cu yd |
| Cutting Depth | 21.90 in (55.63 cm) |
| Height | 36.90 in (93.73 cm) |
| Width | 8.10 ft (2.47 m) |
| Fops | SAE J231-JAN81, ISO 3449-92 |
|---|---|
| Rops | SAE J397-OCT95, SAE J1040-MAY94, ISO 3471-94, ISO 3164-95 |
| Drive Pumps | 2 |
|---|---|
| Max Speed - Forward | 5.60 mph (9.01 kph) |
| Max Speed - Reverse | 6.00 mph (9.66 kph) |
| Maximum Travel Speed - Forward | 5.60 mph (9.01 kph) |
| Maximum Travel Speed - Reverse | 6.00 mph (9.66 kph) |
| Number Of Forward Gears | 1 |
| Number Of Reverse Gears | 1 |
| Relief Valve Settings | 6380 psi |
| Track Motors | 2 |
| Transmission Type | dual path, closed loop hydrostatic |
| Ground Contact Area | 2586 in2 |
|---|---|
| Ground Contact Area - Lgp | 4045 in2 |
| Ground Contact Area - Xl | 2586 in2 |
| Ground Pressure | 6.27 psi |
| Ground Pressure - Lgp | 4.24 psi |
| Ground Pressure - Xl | 6.27 psi |
| Length - Track On Ground - Lgp | 81.00 in (205.74 cm) |
| Length - Track On Ground - Xl | 81.00 in (205.74 cm) |
| Number Of Shoes Per Side | 39 |
| Number Of Track Rollers Per Side | 6 |
| Shoe Width - Lgp | 25.00 in (63.50 cm) |
| Shoe Width - Xl | 16.00 in (40.64 cm) |
| Standard Shoe Size | 16.00 in (40.64 cm) |
| Track Gauge | 4.76 ft (1.45 m) |
| Track Gauge - Lgp | 66.00 in (167.64 cm) |
| Track Gauge - Xl | 57.00 in (144.78 cm) |
| Operating Weight - Lgp | 17,160.00 lbs (7,783.65 kg) |
|---|---|
| Operating Weight - Xl | 16,227.00 lbs (7,360.45 kg) |
| Control | Pilot hydraulic |
|---|---|
| Drum Capacity - Optional Cable | 257.00 ft (78.33 m) |
| Drum Capacity - Recommended Cable | 371.00 ft (113.08 m) |
| Drum Diameter | 10.00 in (25.40 cm) |
| Drum Width | 10.80 in (27.43 cm) |
| Maximum Line Pull - Bare Drum | 40,000.00 lbs (18,143.72 kg) |
| Maximum Line Pull - Full Drum | 25,000.00 lbs (11,339.82 kg) |
| Maximum Line Speed - Bare Drum | 132 ft/min |
| Maximum Line Speed - Full Drum | 207 ft/min |
| Overall Width | 29.20 in (74.17 cm) |
| Rope Diameter - Optional | 0.80 in (2.03 cm) |
| Rope Diameter - Recommended | 0.70 in (1.78 cm) |
| Speed | Variable |
| Throat Clearance | 6.80 in (17.27 cm) |
| Weight | 1,345.00 lbs (610.08 kg) |
| Winch Drive | Hydrostatic |
| Winch Length | 27.80 in (70.61 cm) |