Construction Equipment Guide
470 Maryland Drive
Fort Washington, PA 19034
800-523-2200
| 1st | 6.9 4.3 - Starting 2017 |
|---|---|
| 2nd | 12.0 7.5 - Starting 2017 |
| 3rd | 25.7 16.0 - Starting 2017 |
| 4th | 25.7 16.0 - Starting 2017 |
| 5th Speeds Reverse | 24.50 mph (39.50 km/h) - Starting 2017 |
| A Height to top of exhaust pipe | 134.00 in (3,412.00 mm) - Starting 2017 |
| B Height to top of engine compartment | 106.00 in (2,694.00 mm) - Starting 2017 |
| Bore | 4.10 in (105.00 mm) - Starting 2017 |
| Breakout force | 31,380.00 lbf (139.00 kN) - Starting 2017 |
| C Height to top of ROPS | 136.00 in (3,443.00 mm) - Starting 2017 |
| Capacity - 110% | 5.47 cu yd (4.18 cu m) - Starting 2017 |
| Capacity - rated | 4.97 cu yd (3.80 cu m) - Starting 2017 |
| D Hinge pin height at carry position | 25.00 in (642.00 mm) - Starting 2017 |
| Digging depth | 2.60 in (68.00 mm) - Starting 2017 |
| Dump clearance at full lift and - 45° discharge angle | 118.00 in (3,007.00 mm) - Starting 2017 |
| Dump clearance at full lift and - F Hinge pin height at full lift | 165.00 in (4,182.00 mm) - Starting 2017 |
| Dump clearance at maximum lift and 45° discharge | 106.00 in (2,707.00 mm) - Starting 2017 |
| Emission Standards | Tier 3 equivalent - Starting 2017 |
| engine displacement | 427.80 cu in (7.01 L) - Starting 2018 |
| Engine Model | C7.1 ACERT - Starting 2017 |
| Fuel Tank Capacity | 72.60 US gal (275.00 L) - Starting 2017 |
| G Maximum overall height | 224.00 in (5,690.00 mm) - Starting 2017 |
| Ground Clearance | 15.00 in (385.00 mm) - Starting 2017 |
| Ground clearance (std. tires) | 14.00 in (365.00 mm) - Starting 2017 |
| H Maximum digging depth | 3.50 in (90.00 mm) - Starting 2017 |
| High Lift Adjustment - Breakout force | -2,054.00 lbf (-9.00 kN) - Starting 2017 |
| Hydraulic Cycle Time, - Rated Load in Bucket - Dump (at Maximum Raise) | 1.4 sec - Starting 2017 |
| Hydraulic Cycle Time, - Rated Load in Bucket - Lower (Empty, Float Down) | 2.8 sec - Starting 2017 |
| Hydraulic Cycle Time, - Rated Load in Bucket - Raise (from Carry Position) | 5.3 sec - Starting 2017 |
| Hydraulic Cycle Time, - Rated Load in Bucket - Total | 9.5 sec - Starting 2017 |
| Hydraulic Tank Capacity | 33.00 US gal (125.00 L) - Starting 2017 |
| J Machine center point to axle | 66.00 in (1,675.00 mm) - Starting 2017 |
| K Wheel base | 132.00 in (3,350.00 mm) - Starting 2017 |
| L Radius of tire | 29.00 in (744.00 mm) - Starting 2017 |
| Loader clearance circle with bucket at carry position | 272.00 in (6,888.00 mm) - Starting 2017 |
| M Maximum overall length | 335.00 in (8,489.00 mm) - Starting 2017 |
| Maximum Engine: Gross | 262.00 hp (196.00 kW) - Starting 2017 |
| Maximum Engine: Net | 248.00 hp (185.00 kW) - Starting 2017 |
| Maximum Net Power Engine RPM | 2000 rpm - Starting 2017 |
| N Reach at full lift | 51.00 in (1,299.00 mm) - Starting 2017 |
| No. Cylinders | 6 - Starting 2017 |
| O Maximum rollback at maximum lift | 60 deg - Starting 2017 |
| Operating weight | 42,686.00 lbs (19,368.00 kg) - Starting 2017 |
| Operating weight* | 42,686.00 lbs (19,368.00 kg) - Starting 2018 |
| Overall height with bucket at maximum lift | 230.00 in (5,828.00 mm) - Starting 2017 |
| Overall length | 344.00 in (8,731.00 mm) - Starting 2017 |
| P Maximum rollback at carry height | 49 deg - Starting 2017 |
| Q Maximum rollback at ground | 40 deg - Starting 2017 |
| Reach at level lift arm and bucket level | 121.00 in (3,094.00 mm) - Starting 2017 |
| Reach at maximum lift and 45° discharge | 55.00 in (1,421.00 mm) - Starting 2017 |
| Static tipping load, articulated (no tire deflection) | 26,798.00 lbs (12,158.00 kg) - Starting 2017 |
| Static tipping load, articulated (no tire deflection)* | 26,798.00 lbs (12,158.00 kg) - Starting 2018 |
| Static tipping load, articulated (with tire deflection) | 25,147.00 lbs (11,409.00 kg) - Starting 2017 |
| Static tipping load, articulated (with tire deflection)* | 25,147.00 lbs (11,409.00 kg) - Starting 2018 |
| Static tipping load, straight (no tire deflection) | 30,964.00 lbs (14,049.00 kg) - Starting 2017 |
| Static tipping load, straight (no tire deflection)* | 30,964.00 lbs (14,049.00 kg) - Starting 2018 |
| Static tipping load, straight (with tire deflection) | 29,326.00 lbs (13,306.00 kg) - Starting 2017 |
| Static tipping load, straight (with tire deflection)* | 29,326.00 lbs (13,306.00 kg) - Starting 2018 |
| Stroke | 5.30 in (135.00 mm) - Starting 2017 |
| Tires used for measurements | L3 Michelin XHA2 - Starting 2017 |
| Tread Width | 84.00 in (2,140.00 mm) - Starting 2017 |
| Tread width (std. tires) | 84.00 in (2,140.00 mm) - Starting 2017 |
| Width | 117.00 in (2,994.00 mm) - Starting 2017 |
| Width Over Tires | 110.00 in (2,790.00 mm) - Starting 2017 |
| Width over tires (std. tires) | 111.00 in (2,814.00 mm) - Starting 2017 |
| Bucket Range | 2.7-4.4 m? (3.5-5.8 yd3) |
|---|
| Bucket Capacities | 2.7-4.4 m? (3.5-5.8 yd3) |
|---|
| Centerline Of Rear Axle To Edge Of Counterweight | 7.17 ft (2.19 m) |
|---|---|
| Centerline Of Rear Axle To Hitch | 5.50 ft (1.68 m) |
| Ground Clearance | 1.20 ft (0.37 m) |
| Height - Top Of Exhaust Pipe | 11.19 ft (3.41 m) |
| Height - Top Of Hood | 8.83 ft (2.69 m) |
| Height - Top Of Rops | 11.33 ft (3.45 m) |
| Hinge Pin Height At Carry Height | 2.50 ft (0.76 m) |
| Hinge Pin Height At Maximum Lift | 14.72 ft (4.49 m) |
| Lift Arm Clearance At Maximum Lift | 12.44 ft (3.79 m) |
| Maximum Width - Over Tires - Loaded | 9.33 ft (2.84 m) |
| Note | All dimensions are approximate and based on Michelin 23.5R25 XHA2 L3 radial tires. |
| Overall Length - Without Bucket | 24.75 ft (7.54 m) |
| Rack Back - Carry Height | 54 degrees |
| Rack Back - Maximum Lift | 66 degrees |
| Rack Back At Ground | 45 degrees |
| Tread Width | 7.00 ft (2.13 m) |
| Wheel Base | 11.00 ft (3.35 m) |
| Centerline Of Rear Axle To Edge Of Counterweight | 7.08 ft (2.16 m) |
|---|---|
| Centerline Of Rear Axle To Hitch | 5.50 ft (1.68 m) |
| Ground Clearance | 1.20 ft (0.37 m) |
| Height - Top Of Exhaust Pipe | 11.19 ft (3.41 m) |
| Height - Top Of Hood | 8.83 ft (2.69 m) |
| Height - Top Of Rops | 11.33 ft (3.45 m) |
| Hinge Pin Height At Carry Height | 2.11 ft (0.64 m) |
| Hinge Pin Height At Maximum Lift | 13.72 ft (4.18 m) |
| Lift Arm Clearance At Maximum Lift | 11.89 ft (3.62 m) |
| Maximum Width - Over Tires - Loaded | 9.33 ft (2.84 m) |
| Note | All dimensions are approximate and based on Michelin 23.5R25 XHA2 L3 radial tires. |
| Overall Length - Without Bucket | 23.39 ft (7.13 m) |
| Rack Back - Carry Height | 49 degrees |
| Rack Back - Maximum Lift | 60 degrees |
| Rack Back At Ground | 40 degrees |
| Tread Width | 7.00 ft (2.13 m) |
| Wheel Base | 11.00 ft (3.35 m) |
| Displacement | 427.00 cu in (6,997.29 cu cm) |
|---|---|
| Engine Model | Cat C7.1 ACERT |
| Maximum Gross Power - 2,000 Rpm - Iso 14396 - Metric | 195 kW (265 hp) |
| Maximum Net Torque - 1,400 Rpm | 726.00 lbs ft (984.31 nm) |
| Net Power - Iso 9249 | 252.00 hp (187.92 kw) |
| Peak Gross Torque - 1,400 Rpm - Iso 14396 | 774.00 lbs ft (1,049.39 nm) |
| Hydraulic Cycle Time - Total | 9.5 s |
|---|---|
| Implement Pump Type | Variable Axial Piston |
| Implement System - Maximum Operating Pressure | 4047 psi |
| Implement System - Maximum Pump Output At 2,150 Rpm | 64.70 gpm (244.89 lpm) |
| Breakout Force | 32,822.00 lbs (14,887.83 kg) |
|---|---|
| Note (1) | For a machine configuration as defined under ?Weight.? |
| Note (2) | Full compliance to ISO 143971:2007 Sections 1 thru 6, which requires 2% verification between calculations and testing. |
| Static Tipping Load - Full 40 Degrees Turn - No Tire Deflection | 27,459.00 lbs (12,455.21 kg) |
| Static Tipping Load - Full 40 Degrees Turn - With Tire Deflection | 25,794.00 lbs (11,699.98 kg) |
| Cooling System | 14.30 gal (54.13 l) |
|---|---|
| Crankcase | 5.30 gal (20.06 l) |
| Differential - Final Drives - Front | 11.40 gal (43.15 l) |
| Differential - Final Drives - Rear | 11.40 gal (43.15 l) |
| Fuel Tank | 72.60 gal (274.79 l) |
| Hydraulic Tank | 33.00 gal (124.91 l) |
| Transmission | 11.40 gal (43.15 l) |
| Note (1) | *Distance of 15 m, moving forward in second gear ratio. |
|---|---|
| Note (2) | **For machines in countries that adopt the ?EU Directives.? |
| Note (3) | ***European Union Directive ?2000/14/EC? as amended by ?2005/88/EC.? |
| With Cooling Fan Speed At 70% Of Maximum Value - Exterior Sound Power Level (Iso 6395:2008)** | 104 LWA*** |
| With Cooling Fan Speed At 70% Of Maximum Value - Operator Sound Pressure Level (Iso 6396:2008)** | 69 dB(A) |
| With Cooling Fan Speed At Maximum Value - Exterior Sound Power Level (Iso 6395:2008) | 107 dB(A) |
| With Cooling Fan Speed At Maximum Value - Exterior Sound Pressure Level (Sae J88:2013) | 75 dB(A)* |
| With Cooling Fan Speed At Maximum Value - Operator Sound Pressure Level (Iso 6396:2008) | 72 dB(A) |
| Forward - 1 | 4.30 mph (6.92 kph) |
|---|---|
| Forward - 2 | 7.50 mph (12.07 kph) |
| Forward - 3 | 12.00 mph (19.31 kph) |
| Forward - 4 | 16.00 mph (25.75 kph) |
| Forward - 5 | 24.50 mph (39.43 kph) |
| Note | Maximum travel speed in standard vehicle with empty bucket and standard L3 tires with 787 mm roll radius. |
| Reverse - 1 | 4.30 mph (6.92 kph) |
| Reverse - 2 | 7.50 mph (12.07 kph) |
| Reverse - 3 | 16.00 mph (25.75 kph) |
| Note | Weight based on a machine configuration with Michelin 23.5R25 XHA2 L3 radial tires, full fluids, operator, standard counterweight, cold start, roading fenders, Product Link?, open/open axles (front/rear), power train guard, secondary steering, sound suppression and a 3.4 m3 general purpose bucket with BOCE. |
|---|---|
| Operating Weight | 42,159.00 lbs (19,123.02 kg) |