| Air Conditioning System |
|
Air Conditioning |
The air conditioning system on this machine contains the fluorinated greenhouse gas refrigerant R134a (Global Warming Potential = 1430). The system contains 2.0 kg (4.4 lb) of refrigerant which has a CO2 equivalent of 2.860 metric tonne (2.76 ton). |
| Blade Range |
|
Blade Tip Range - Backward |
5 degrees |
|
Blade Tip Range - Forward |
40 degrees |
|
Circle Centershift - Left |
26 in (65 cm)
|
|
Circle Centershift - Right |
21 in (52 cm)
|
|
Maximum Depth Of Cut |
23 in (59 cm)
|
|
Maximum Lift Above Ground |
17 in (42 cm)
|
|
Maximum Shoulder Reach Outside Of Tires - Left |
74 in (187 cm)
|
|
Maximum Shoulder Reach Outside Of Tires - Right |
79 in (200 cm)
|
|
Moldboard Sideshift - Left |
29 in (74 cm)
|
|
Moldboard Sideshift - Right |
31 in (79 cm)
|
| Engine |
|
Base Power (1st Gear) - Net |
238 hp (177 kw)
|
|
Bore |
5 in (13 cm)
|
|
Displacement |
763 cu in (12,503 cu cm)
|
|
Emissions |
Tier 4 Final/Stage IV, Tier 3/Stage IIIA equivalent or Tier 2/Stage II equivalent |
|
Engine Model |
Cat C13 ACERT VHP |
|
Maximum Altitude - Full Power |
13,900 ft (4,237 m)
|
|
Maximum Altitude - Full Power (Tier 2) |
12,049 ft (3,673 m)
|
|
Maximum Altitude - Full Power (Tier 3) |
14,349 ft (4,374 m)
|
|
Maximum Torque - Vhp Plus |
1,137 lbs ft (1,542 nm)
|
|
Note (1) |
Net power is tested per ISO 9249, SAE J1349, and EEC 80/1269 Standards in effect at the time of manufacture. |
|
Note (2) |
Optimized VHP Plus is standard for the 14M3. |
|
Note (3) |
Net power advertised is the power available at rated speed of 1,850 rpm, measured at the flywheel when engine is equipped with fan, air cleaner, muffler and alternator. |
|
Note (4) |
Power as declared per ISO 14396 Rated rpm 1,850 VHP+ = 228 kW (306 hp) |
|
Note (5) |
Cat engines equipped with a Selective Catalytic Reduction (SCR) system are required to use: Diesel Exhaust Fluid (DEF) which meets the requirements outlined in the International Organization for Standardization (ISO) standard 22241-1. |
|
Number Of Cylinders |
6 |
|
Speed At Rated Power |
1,850 rpm |
|
Standard - Fan Speed - Maximum |
1,600 rpm |
|
Standard - Fan Speed - Minimum |
550 rpm |
|
Standard Capability |
122 degrees |
|
Stroke |
6 in (16 cm)
|
|
Torque Rise |
41 % |
| Frame |
|
Circle - Outer Diameter |
72 in (182 cm)
|
|
Front Axle - Total Oscillation Per Side |
32 degrees |
|
Front Axle - Wheel Lean - Left/Right |
17 degrees |
| Moldboard |
|
Arc Radius |
16 in (41 cm)
|
|
Blade Height - With Cutting Edge |
25 in (63 cm)
|
|
Blade Height - Without Cutting Edge |
23 in (58 cm)
|
|
Blade Width |
14 ft (4 m)
|
|
Blade Width - With End Bits |
169 in (429 cm)
|
|
Blade Width - Without End Bits |
164 in (417 cm)
|
|
Throat Clearance |
5 in (12 cm)
|
| Weights |
|
Gross Vehicle Weight - Base* - Front Axle |
13,994 lbs (6,348 kg)
|
|
Gross Vehicle Weight - Base* - Rear Axle |
36,994 lbs (16,780 kg)
|
|
Gross Vehicle Weight - Base* - Total |
50,980 lbs (23,124 kg)
|
|
Gross Vehicle Weight - Typically Equipped - Front Axle |
15,245 lbs (6,915 kg)
|
|
Gross Vehicle Weight - Typically Equipped - Rear Axle |
42,005 lbs (19,053 kg)
|
|
Gross Vehicle Weight - Typically Equipped - Total |
57,250 lbs (25,968 kg)
|
|
Note |
*Base operating weight calculated on standard machine configuration with 20.5 R25 tires, full fuel tank operator and ROPS cab. |
|
Operating Weight - Typically Equipped |
57,250 lbs (25,968 kg)
|
