Description:
2004 CME 55LC – Rod Clamp, Breakout, Auto Hammer – DRM Shop Refresh Included
Make / Model: CME 55LC
Year: 2004
Serial Number: 328545
Hours: 12,000+ showing on control display
Engine: Diesel – appears to have been replaced at some point in the rig’s life
Condition: Good – Recently Came Off Project
Price: $149,500 with DRM Shop Refresh
Limited As-Is Price: $129,500 before shop work begins
????????????????????????????????
This 2004 CME 55LC is a very well-equipped geotechnical rig with the features most contractors want already on the machine.
It is equipped with a rod clamp, breakout wrench, slide base, wiggle tail, automatic hammer, 3L6 Moyno pump, main winch, two tool winches, wireline winch, front water tank, front auger storage, 10-foot rod storage, and extensive custom tooling storage throughout the rig.
The machine just came off a project and is now getting ready to come through the Drill Rig Marketplace shop for a one-week refresh.
For a limited time, the seller is also willing to sell it as-is before that work begins.
????????????????????????????????????
Rod clamp
Breakout wrench
Hydraulic slide base
Wiggle tail
Automatic SPT hammer
Moyno 3L6 water pump
Main winch
Two tool winches
Wireline winch
Front-mounted water tank
Front auger storage
10' rod storage
Custom helper-side auger / tooling rack
Split spoon holders
Shelby tube holders
Roller bit holders
Additional custom fabrication and tooling storage throughout the rig
???????????????????? & ????????????????????????
The control display is showing a little over 12,000 hours.
The engine appears to have been replaced at some point during the machine’s life based on its current appearance, but the exact replacement history and actual engine hours are not documented.
Because of that, the listing is being represented based on the hours shown on the machine rather than making assumptions about actual engine time.
????????????????????????????????????
The rig is in good overall working condition and recently came directly off a project.
It is not being represented as a fully rebuilt machine. It is an older working rig with a strong equipment package that is getting ready to receive a focused DRM shop refresh.
The goal of that work is to address the critical items, clean up age-related issues, service the machine properly, and give the buyer a much more dialed-in rig without turning it into a full ground-up restoration.
???????????? ????????????-???????????????? ???????????????? ????????????????????????????
At the $149,500 asking price, the rig will receive approximately one week of shop attention before delivery.
Planned work can include:
Full operational inspection
Function testing of major drilling systems
Electrical cleanup and repair of critical issues
Repair of safety-related electrical items as needed
Replacement of failed or visibly compromised hydraulic hoses
Repair of active hydraulic leaks
Full fluid and filter service
Inspection and adjustment of the automatic hammer
Inspection and testing of the rod clamp and breakout wrench
Inspection and testing of the 3L6 Moyno pump
Inspection and testing of all winches
Minor mechanical repairs discovered during inspection
Pressure wash and degrease
Cosmetic paint refresh
Final operational testing
DRM service report documenting completed work
Any major component failure discovered during inspection that falls outside the normal scope of the refresh would be reviewed separately before additional work is performed.
???????????????????????????? ????????-???????? ????????????????????????????????????????????
Before the rig enters the shop, the seller is willing to offer it as-is for $129,500.
That gives a buyer who prefers to handle their own repairs, service, or cosmetic work the opportunity to purchase the rig at a lower price.
Once DRM begins the shop refresh, the as-is pricing will no longer apply.
???????????????????????????? ???????????????????????????????? ????????????????????????????????????
Need tooling to go with the rig?
Drill Rig Marketplace can quote a complete tooling package based on your drilling application, including hollow stem augers, drill rod, casing, bits, adapters, sampling tools, split spoons, Shelby tubes, and other accessories as needed.
We can help put together the rig and tooling as a complete package so it is ready to go to work when it arrives.
???????????????????????????????? ????????????????
This rig already has the expensive pieces most buyers would want to add later.
You have the rod clamp, breakout wrench, slide base, wiggle tail, auto hammer, 3L6 Moyno pump, four winches, water tank, auger storage, rod storage, and a lot of useful custom tooling storage already built into the machine.
At $129,500, you can buy it as it sits and handle the work yourself.
At $149,500, DRM will put it through the shop, address the critical issues we find, service it, replace necessary hoses, clean up the electrical, freshen up the cosmetics, and provide a documented service report showing what was completed.
For somebody looking for a well-equipped CME 55LC without stepping into the cost of a newer machine, this is a strong package.
Asking Price: $149,500 with DRM Shop Refresh
Limited As-Is Price: $129,500 before shop work begins
