Description:
Make / Model: CME 75 High Torque
Year: 1987
Rig Hours: 9,145
Deck Engine: Cummins 6B 5.9 Diesel
Carrier: 2002 International 4800 AWD
Truck Mileage: Approximately 43,000 Miles
Pullback: 30,000 lb
Rotary Torque: Up to 11,000 ft-lb
Location: Midwest U.S.
Condition: Good – Operational and Still Working
Asking Price: $140,000 USD
????????????????????????????????
This 1987 CME 75 High Torque is mounted on a 2002 International 4800 AWD chassis and is set up as a serious geotechnical, auger, core, and rotary drilling package.
The rig has 9,145 hours and is powered by a Cummins 6B 5.9 diesel deck engine. The truck has only approximately 43,000 miles and is equipped with an automatic transmission and all-wheel drive.
This is not a stripped-down CME 75. It is equipped with a hydraulic rod clamp and breakout wrench, fluted Kelly, slide base with in/out and side-to-side movement, 3L8 Moyno pump, cathead, three winches, and sliding auger racks.
A substantial hollow-stem auger and drill pipe package is also included.
????????????????????????????????????
- Cummins 6B 5.9 diesel deck engine
- 9,145 rig hours
- Approximately 30,000 lb pullback
- High-torque rotary head
- Approximately 100–700 RPM
- Up to approximately 11,000 ft-lb rotary torque
- Hydraulic rod clamp
- Hydraulic breakout wrench
- Fluted Kelly
- Hydraulic check assembly
- Slide base – in/out and side-to-side
- Moyno 3L8 water pump with standpipe
- Cathead
- Main winch
- Auxiliary / tool winch
- Wireline winch
- Sliding auger racks
???????????????????? ????????????????????????????
- Main hydraulic winch – approximately 7,000 lb
- Auxiliary winch – approximately 3,200 lb
- Wireline winch – approximately 900' capacity
????????????????????
The rig is mounted on a 2002 International 4800 AWD.
Truck features include:
- Approximately 43,000 miles
- Automatic transmission
- All-wheel drive
- 35,000 lb GVWR
- Approximately 32,000 lb operating weight with augers and rods
- Current DOT inspection reported by seller
The low-mileage AWD carrier is a major part of the value of this package, especially for contractors working on rough access sites where a standard 4x2 drill truck can become a limitation.
???????????????????????????? ????????????????????????????????
The seller has also included a substantial drilling-tool package:
- Approximately 180' of 4-1/4" ID Acker hollow-stem auger
- Bits and cap
- AWJ rods
- Retriever
- Approximately 100' of 6-1/4" ID Acker hollow-stem auger
- Bits and cap
- Approximately 45' of 8-1/4" ID CME hollow-stem auger
- Bits and cap
- Approximately 265' of NWJ x 10' drill pipe
- Subs
- Collars
- Bits
- Bails
This gives a buyer a significant amount of working tooling to go with the machine instead of starting from scratch after purchasing the rig.
????????????????????????????????????
The seller describes the rig as well maintained and in good overall operating condition.
The machine is still operational and being used regularly. No known mechanical issues were reported in the seller's submission.
Cosmetically, it shows normal age and use, but the photos show a complete working machine with the major drilling systems, storage, racks, and carrier intact.
????????????????????????????????????????????????
- Geotechnical drilling
- Hollow-stem auger drilling
- Soil sampling
- SPT work
- Core drilling
- Rotary drilling
- Environmental drilling
- Monitoring well installation
???????????????????????????? ???????????????????????????????? ????????????????????????????????????
Need additional tooling beyond what is already included?
Drill Rig Marketplace can quote augers, drill rods, casing, bits, adapters, sampling tools, core tooling, and other accessories based on your drilling application.
???????????????????????????????? ????????????????
There is a lot here for the money.
You are getting a high-torque CME 75 with 30,000 lb pullback, rod clamp, breakout wrench, slide base, 3L8 Moyno, three winches, sliding auger racks, and a Cummins 6B deck engine.
Then you add a 2002 International 4800 AWD chassis with only about 43,000 miles and a sizable tooling package already included.
It is an older working rig and looks like one, but it is equipped to make money. For a contractor looking for a capable CME 75 package without getting into late-model six-figure pricing, this one deserves a serious look.
