EQUIPMENT ON ORDER- PO#2051430, Equipment As Follows:, METSO 7x20 THREE DECK HORIZONTAL SCREEN (1 LEFT HAND DRIVE/1 RIGHT HAND DRIVE), The new triple shaft Metso horizontal screen is designed for maximum efficiency and performance, Coil Springs and dampers, 3/8” Thick Side Plates with Huck Bolt Construction, Side Tension decks with seal strips for 4’ screen panels, Heavy Duty Tube Steel Decks with Herringbone Cross Bracing, Vibrating Mechanism (190mm bearings) with Oil lubrication, Carriage Bolts used to retain clamp bars – Standard is 4’ long bars, AR lined Feedbox and AR lined Discharge Lip, Variable speed drive standard with motor mount and belt guard and tensioning device, Hand access on triple deck screens. Spray Bar knockouts, bottom deck Feed end curtain, Hand of drive is Right Hand, Side tension single crown, Medium Scalper Deck – includes heavy duty side tension top deck, heavier feedbox liner and heavier top discharge lip., Media not included, Side tension single crown, Media not included, Side tension single crown, Media not included, Installation Angle 0°, Elliptical stroke 5/8” -3/4”, RPM 675-875, Separating G Force: 4.8-6.5, Top deck, Middle deck, Bottom deck,, GREYHAWK PORTABLE TANDEM SCREEN PLANT CHASSIS, MAIN CHASSIS, Heavy Duty Mainbeam, Quad-axle Hutch Spring Suspension with 49-1/2” axle spacing, Qty 16 11R22.5 tires on hub piloted wheels, Air controlled brakes on all four axles, LED side marker and tail lights, Catwalk on three sides of each screen, diamond floor plate, including handrails and toe boards, with (2) access ladders included., Fold down kingpin supports, Chutes-Primary & Secondary Screen, Top deck to top cross conveyor, Middle deck to middle cross conveyor/bottom cross conveyor/fines conveyor, Bottom deck to middle cross conveyor/bottom cross conveyor/fines conveyor,, OVERHEAD SPLITTER CONVEYOR-42”, Channel frame design, Superior 5” CEMA C channel mount picking idlers, Superior 5” CEMA C return idlers, Superior Exterra belt scraper, 3 ply, 3/16” top cover conveyor belting, Full length rubber skirting, Head Pulley, VDG motorized drum pulley 16”, 20HP motor, Dodge SCM pillow block bearings, Tail Pulley, Superior 12” wing pulley, Dodge SCM bearings, Takeups,, UNDERSCREEN CONVYEOR (PRIMARY SCREEN)-60”, Channel frame design, Superior 5” CEMA C channel mount picking idlers, Superior 5” CEMA C return idlers, Superior Exterra belt scraper, 3 ply, 3/16” top cover conveyor belting, Full length rubber skirting, Head Pulley, Superior 12” drum pulley, Dodge SCM pillow block bearings, Master PT #5 shaft mount reducer, WEG 20HP motor, Takeups, Tail Pulley, Superior 12” wing pulley, Dodge SCM bearings,, UNDERSCREEN CONVYEOR (SECONDARY SCREEN)-60”, Channel frame design, Superior 5” CEMA C channel mount picking idlers, Superior 5” CEMA C return idlers, Superior Exterra belt scraper, 3 ply, 3/16” top cover conveyor belting, Full length rubber skirting, Head Pulley, Superior 12” drum pulley, Dodge SCM pillow block bearings, Master PT #5 shaft mount reducer, WEG 20HP motor, Tail Pulley, Superior 12” wing pulley, Dodge SCM bearings, Takeups,, TOP CROSS CONVYEOR- QTY (1)-48”, Channel frame design, Superior 5” CEMA C flat carrier idlers, Superior 5” CEMA C return idlers, Superior Exterra belt scraper, 3 ply, 3/16” top cover conveyor belting, Full length rubber skirting, Head Pulley, Superior 10” drum pulley, Dodge SCM pillow block bearings, Master PT #4 shaft mount reducer, WEG 10HP motor, Tail Pulley, Superior 10” wing pulley, Dodge SCM bearings, Takeups,, CROSS CONVYEOR- QTY (4)-24”, Channel frame design, Superior 5” CEMA C flat carrier idlers, Superior 5” CEMA C return idlers, Superior Exterra belt scraper, 3 ply, 3/16” top cover conveyor belting, Full length rubber skirting, Head Pulley, Superior 10” drum pulley, Dodge SCM pillow block bearings, Master PT #2 shaft mount reducer, WEG 7.5HP motor, Tail Pulley, Superior 10” wing pulley, Dodge SCM bearings, Takeups,, HYDRAULICS:, Gas powered hydraulic power unit with electric start and recoil backup, (6) Hydraulic jacklegs with lock-out valves, 18” stroke, The hydraulic jack assemblies are designed for service as a “Run-on” jack, however, we highly recommend the use of cribbing to properly support the portable chassis, Six bank valve body for independent control of each jackleg, Raise/lower of the overhead splitter conveyor,, ELECTRICAL:, NEMA4 enclosure, Enclosure is bolted to a steel support frame for setting on grade during operation, Lifting eyes, Connected to plant with 15’ of cable to allow the customer to position the enclosure, Door interlocked disconnect linkage, Warning horn, Circuit breakers, NEMA rated starters, Overhead Splitter Conveyor – 1@20HP/each, Primary Underscreen Discharge Conveyor – 1@20HP/each, Secondary Underscreen Discharge Conveyor – 1@20HP/each, Top Cross Conveyor – 1@10HP/each, Cross Conveyors –
[email protected]/each, Screen – 2@50HP/each, Hour meter, Pushbutton start/stop control,, SAFETY GUARDS:, We install all standard guarding, customer will be responsible for compliance with local codes., GENERAL:, Paint, Sandblasted, Two-part epoxy primer, Two-part urethane topcoat, Chassis Color-GH Beige, Handrail & Guarding Color-GH Orange, Decals-Orange & grey striping, (2) sets of owners/parts manuals.
